...
Questions to Ask When Contacting a Bag Making Machine Company
November 12, 2026

Questions to Ask When Contacting a Bag Making Machine Company

The first reply from a bag making machine company tells you more than the quotation that follows. A supplier that answers with a model number and a price is selling a catalogue item. A supplier that asks about your bag drawing, film structure and shift pattern before quoting is thinking about the machine you will actually run for the next decade.

These are the questions worth asking in that first exchange, grouped by what they reveal. Ask them in one email rather than six, and note not only the answers but how long they take to arrive.

Questions About the Machine Itself

Start with the specification, because vague answers here predict vague machines:

● Which model are you quoting, and what is its rated speed at my bag size? — not the maximum, but the figure at your length, width, film and print status. If the reply repeats the catalogue maximum, ask again with your dimensions.

● How many servo axes, and what does each one drive? — feed, sealing, knife, unwind, handle unit. The answer separates a genuinely servo-driven machine from one with a single servo and three inverters.

● What is the minimum and maximum bag size, measured? — a machine quoted “up to 700 mm” may not run 250 mm bags reliably, because the knife stroke and stacker geometry have a floor as well as a ceiling.

● How is sealing temperature controlled and how often is it calibrated? — a thermocouple with a controller is standard; how the supplier verifies it is not. Ask whether a calibration procedure ships with the manual.

● What does changeover between bag sizes involve, and how long does it take? — minutes and tools. A machine that needs half a shift to change bag width will be run on one size whether or not your order book agrees.

Our plastic bag making machine range is built in families for exactly this reason: a side seal bag making machine and a bottom seal machine answer different questions, and the model page should state which bag sizes each covers.

Questions About Film and Bags

The machine is only half the process. The film decides the rest:

● What film structures has this model run, and at what thickness? — a machine proven on 15 to 30 micron HDPE may behave differently on 80 micron coextruded film, because the sealing and cooling time budget changes.

● Can you run my film before shipment? — a trial on your own roll is the single most valuable test available. Ask for a video of the run with your bag size, and for the seal strength result.

● What waste percentage should I expect? — start-up, splices, and edge trim. A supplier who answers “almost none” has either not measured or is not telling you.

● Can the machine handle printed film with registration? — and if so, what is the photocell brand and the correction range in millimetres.

A supplier that asks for a film sample before quoting is doing engineering. One that quotes immediately without asking is doing sales.

Bag making machine production line in Chovyting factory

Questions About the Factory and Quality Control

These determine whether the machine you receive matches the machine you were shown:

● Is the machine assembled in your own factory or by a partner? — both models exist in China. Neither is disqualifying, but you should know which one you are buying, because it decides who answers when something goes wrong.

● What is inspected before shipment, and can I see the report? — look for a checklist that includes running time, seal strength, bag length tolerance and electrical safety, not just “machine tested”.

● Which components are branded, and which are local? — servo brand, PLC brand, photocell brand, pneumatic brand, bearing brand. Branded components matter mainly because they are replaceable anywhere.

● Can I visit, or can we do a live video walkthrough? — a video call through the assembly bay answers questions a brochure cannot. Our team runs these routinely for overseas buyers who cannot travel.

For a structured approach to a factory visit, see plastic bag making machine factory visit guide.

Questions About Service, Spares and Support

This is where quotations quietly differ, and where the total cost of ownership is decided:

● What is the warranty period, and what does it exclude? — sealing knives, Teflon tape and photocells are usually consumables. Confirm which parts are covered and for how long.

● How fast do you respond, and through which channel? — a named engineer with WhatsApp and remote access beats a general sales inbox. Ask what the typical response time was in the last three months.

● Can you access the PLC remotely? — remote diagnostics turns a two-week wait for a technician into a same-day parameter fix. Confirm the machine ships with the capability enabled, not as a paid extra.

● Which spare parts should I keep on the shelf? — ask for a recommended first-year kit with prices. A supplier that cannot produce this list has not thought about after-sales.

● How long are spare parts available after the model is discontinued? — ten years is a reasonable expectation for a machine with a twenty-year frame life.

The manufacturer versus supplier comparison explains why these answers differ so much between the two.

Heavy duty bag making machine line with bag samples

Questions About Commercial Terms

Commercial structure tells you who carries the risk:

● What are the payment terms, and what is the balance tied to? — balance against a pre-shipment video test or an inspection is normal. Full payment before shipment shifts all risk to you.

● What is included in installation? — days on site, technician travel, training hours, and what happens if commissioning takes longer than planned.

● Which certifications apply, and can I see the documents? — CE declaration, test reports, and the name of the authorised representative if you sell into the EU.

● What is the lead time, measured from deposit or from drawing approval? — the difference is often three weeks, and it matters when you have a contract start date.

What a Good Answer Looks Like

Compare the texture of the replies, not just the content:

● Good — “At 400 × 300 mm, 25 micron LDPE, unprinted, this model sustains 160 to 180 pcs/min. With print registration, plan on 140 to 150.”

● Weak — “Our machine can reach 250 pcs/min, very fast and stable.”

● Good — “Servo on feed and sealing, inverter on unwind. Four axes total, Delta drives, Panasonic PLC.”

● Weak — “Full servo system, high precision.”

● Good — “Sealing knife life is 6 to 12 months depending on film; replacement is USD 180 and ships from stock.”

● Weak — “The knife is very durable.”

Numbers with conditions attached are the mark of a supplier who has actually run the machine. Adjectives are the mark of a supplier who has run a brochure.

Red Flags Worth Walking Away From

Some answers end the conversation on their own:

● No film trial, no exception — a supplier who will not run your film is asking you to accept the risk of their uncertainty.

● Unwillingness to name component brands — “international brand” is not a brand.

● Warranty shorter than twelve months on the frame and drives — the machine has not been designed to last, or the supplier does not expect to be around.

● Pressure to decide within days — genuine lead times do not collapse because you asked a question. Urgency is a sales technique, not a production constraint.

● No address, no registration number, no factory photos with dates — three basics that take ten minutes to check and are usually omitted by intermediaries.

For the broader due-diligence picture, see how to find reputable bag making machine factories in China.

A Short RFQ That Gets Useful Answers

You do not need a long document. Five lines get a competent engineer moving:

● Bag — type, finished width × length, gusset, handle type, with a drawing or photo.

● Film — structure, thickness in micron, printed or plain, maximum roll diameter.

● Target — pieces per minute you need sustained, and hours per day the machine will run.

● Environment — voltage, frequency, ambient temperature, and whether compressed air is available at 6 bar.

● Ask — recommended model, speed at these conditions, itemised price, lead time, and the acceptance test you propose.

Send the same five lines to three suppliers. The differences in how they respond will tell you more than a week of comparing catalogues, and it costs you one afternoon.

Want to test these questions on a real engineering team?
Send your bag drawing and film structure. You will get a model recommendation, the speed we will guarantee at your conditions, and a component list with brands — before any price discussion.

Send Your Bag Specification

Frequently Asked Questions

What should I ask a bag making machine company first?

Ask which model they recommend for your specific bag size and film, and what speed it will sustain at those conditions. Everything else follows from that answer, including whether the supplier is engineering your requirement or quoting a stock item.

How many suppliers should I contact?

Three is enough. Fewer and you cannot calibrate the answers; more and you spend a month comparing quotations instead of testing one machine. Choose suppliers whose existing customers make products similar to yours.

Should I ask for a video of the machine running my film?

Yes, and ask for it to show the bag coming off the stacker, not just the sealing section. A video of a machine running without film, or a stock promotional clip, tells you nothing about how it handles your material.

What warranty is normal for a bag making machine?

Twelve months on the machine and 24 months on servo drives and the PLC is a common structure. Consumables such as sealing knives, Teflon tape and photocells are usually excluded, which is reasonable as long as the exclusion is written down.

How do I verify a supplier is a real manufacturer?

Check the business registration, ask for a live video walkthrough of the assembly area, and request the name of two customers in your region. A manufacturer can produce all three within a day; a trading company will produce excuses.

What if the supplier will not share component brands?

Treat it as a refusal to be compared. Component brands decide spare-part availability for the next decade, and any supplier with a genuine machine has no reason to hide them.

Should the first order include a spare parts kit?

Yes. Order sealing knives, Teflon tape, photocells, belts and a set of proximity sensors with the machine. Small parts cost little at order and a great deal when a line is stopped and the next shipment is three weeks away.

Related Resources

● How to Compare Plastic Bag Making Machine Manufacturers Before Buying — a scoring method for the shortlist.

● Manufacturer vs Supplier: What’s the Difference — why the same question gets different answers.

● Plastic Bag Making Machine Factory Visit Guide — what to look at when you are standing on the floor.

Coming next: How to Write an Acceptance Test Protocol for a Bag Making Machine, and Remote Diagnostics: What to Ask Before You Need It.

GET A QUOTE NOW