...
Stand Up Pouch Making Machine vs Three-Side Seal Pouch Machine: Key Differences
November 18, 2026

Stand Up Pouch Making Machine vs Three-Side Seal Pouch Machine: Key Differences

Both machines seal laminated film into pouches, both run at similar speeds, and both are sold as “pouch making machines”. The difference is one fold. A stand-up pouch has a bottom gusset that lets it stand; a three-side seal pouch is two flat sheets sealed on three edges. That single structural difference cascades into film structure, sealing geometry, changeover time, machine cost and which filling line the finished pouch can run on.

Buyers who treat the two as interchangeable usually discover the problem at the filling machine, three months after the equipment has been paid for.

How Each Pouch Is Built

The construction decides everything downstream:

● Stand-up pouch — a single web is folded into a W-shaped bottom gusset, then sealed at the two sides and the top. The gusset is what allows the pouch to stand, and it is also what concentrates stress at the bottom corners when the pouch is filled.

● Three-side seal pouch — two webs (or one web folded at the top) are sealed along the two sides and the bottom, leaving the top open for filling. There is no gusset, so the pouch is flat until it is filled, and it stands only if the product itself supports it.

● Four-side seal and flat-bottom variants — a separate family, covered in our comparison of three-side and four-side seal machines.

The laminated pouch making machine series contains both constructions because the market needs both, and because many converters eventually buy a second machine once the product mix widens.

Film Structure Requirements Diverge Quickly

Neither machine is fussy about film in principle, but the practical requirements are different:

● Stand-up pouches need stiffness — a gusset made from soft film folds unevenly and the pouch leans. Typical structures are PET/PE, PET/AL/PE or PET/VMPET/PE at 100 to 150 micron total, with the PET layer providing the body.

● Three-side seal pouches accept softer film — 70 to 120 micron structures are common, and sealant layers can be thinner because there is no gusset to hold shape.

● Both need a sealant layer that seals to itself — PE or CPP. A structure with a sealant that is too thin will fail at the corners where the seal meets the fold.

● Both need registration — printed pouches require a photocell with correction, and the stand-up machine needs it on a web that is also being folded, which is mechanically harder.

Alignment between print and the gusset fold is the single most common quality complaint on stand-up pouches. On a three-side seal pouch, print alignment is forgiving by comparison, because there is no fold to align to.

CW-700SQB stand up pouch making machine square bottom

Output and Format Range

Rated speeds look similar; the useful ranges differ:

● Stand-up pouch machines — the CW-700SQB square bottom pouch machine covers 150 to 650 mm pouch width, runs to 150 pcs/min and 30 m/min, and handles paper-plastic and aluminium-plastic laminates. The “8 side seal” description refers to the number of seal zones on a square-bottom pouch, not to eight separate seal bars.

● Three-side seal machines — the CWZD-600A three side and centre sealing machine runs 40 to 150 pcs/min with pouch lengths from 70 to 500 mm, and adds a six-times skip-feed design for very long formats and a waste film rewinding unit.

● Practical throughput — on both families, plan on 70 to 85 percent of the rated figure for a full shift with printed film, because registration correction and pouch collection both take time.

The format range matters more than the speed for most buyers. A machine that tops out at 400 mm pouch length cannot make a 500 g coffee pouch, no matter how fast it runs.

Changeover and Tooling

Product mix decides whether a machine earns its keep:

● Stand-up pouches — a size change means new gusset forming plates, new seal bars or inserts, new cutters and a new stacker setting. Expect two to four hours with two people, and expect the tooling to be specific to the gusset depth.

● Three-side seal — a size change is mostly seal bar position and cutter length, with the pouch width set by the web width. One to two hours is realistic.

● Tooling cost — a full set for a stand-up pouch format is typically two to three times the cost of a three-side seal set, because the gusset forming hardware is machined rather than adjusted.

If your order book has ten pouch sizes in small volumes, changeover time will dominate your economics and a three-side seal machine will usually win. If you have three sizes in large volumes, the stand-up machine’s slower changeover is irrelevant.

Cost Comparison, Machine and Pouch

Both sides of the ledger matter:

● Machine price — a stand-up pouch machine typically costs 30 to 60 percent more than a comparable three-side seal machine, because of the gusset forming station, the additional servo axes and the tighter registration requirement.

● Film cost — a stand-up pouch uses more film per pouch at the same fill volume, because the gusset consumes material to create volume. On a 500 g fill, expect 10 to 20 percent more film area than a three-side seal pouch of the same capacity.

● Pouch value — the stand-up format sells at a premium and occupies shelf space better, which is why brands choose it for retail and not for industrial packaging.

● Filling cost — stand-up pouches need a filler that opens the pouch and holds it upright; three-side seal pouches run on simpler, faster fill-seal machines.

Which Filling Line the Pouch Fits

This is where the decision is often made for you:

● Premade pouch fillers — designed around stand-up pouches with a top opening. If you already own one, buying a three-side seal machine means buying a second filling line.

● Form-fill-seal machines — a three-side seal pouch is a natural fit for horizontal FFS, where the pouch is formed, filled and sealed in one pass. Buying premade three-side seal pouches only makes sense when volumes are low or the product requires a specific film.

● Retort and high-barrier applications — stand-up pouches with aluminium or metallised layers dominate, because the format survives retort pressure better than a flat pouch.

● Spouted pouches — a separate tooling set on a stand-up machine. Confirm the spout insertion unit is available before assuming a machine can be upgraded later.

CWZD-600A three side seal pouch making machine

How to Choose

Work through these five questions in order. The answer usually becomes obvious by the third:

● Does the product need to stand on a shelf? — if yes, the gusset is not optional, and the decision is made.

● What fill weight and volume? — below 100 g, a flat pouch is usually sufficient and cheaper. Above 500 g, the stand-up format’s stability starts to matter.

● How many sizes per year? — more than six sizes in small volumes favours the three-side seal machine on changeover economics.

● What filling equipment exists or is planned? — match the pouch to the filler, not the other way round.

● What does the customer’s shelf look like? — retail buyers expect stand-up; industrial and refill buyers often prefer flat for cost.

For background on the wider category, see types of pouch making machines and the comprehensive guide to plastic pouch making machines.

Where Buyers Get This Wrong

Four recurring mistakes, all expensive:

● Buying on speed alone — a 150 pcs/min machine that needs four hours of changeover loses to a 100 pcs/min machine with one hour, at any mix with more than four sizes.

● Assuming the film is transferable — a structure optimised for a flat pouch often runs badly as a stand-up pouch, because the gusset needs stiffness the structure does not have.

● Ignoring the filler — the cheapest machine in the project can force the most expensive change to the filling line.

● Underestimating tooling — tooling for four stand-up formats can approach 15 percent of the machine price. Ask for the tooling list per size before signing.

Frequently Asked Questions

Stand-up pouch vs three-side seal pouch: main difference?

The bottom gusset. A stand-up pouch is folded into a W-shaped base that allows it to stand and holds more volume for the same footprint. A three-side seal pouch is flat, sealed on three edges, and stands only if the contents support it.

Can one machine make both pouch types?

Some machines can be configured for multiple formats, but not simultaneously. Centre-seal and three-side seal formats often share a platform; adding stand-up capability usually means a gusset forming station that changes the machine’s mechanical layout. Ask for a written list of formats the machine can produce with which tooling sets.

Which pouch is cheaper to produce?

The three-side seal pouch, on both film and machine cost. It uses less film for the same fill volume, needs a simpler machine, and runs on faster filling equipment. The stand-up pouch costs more and sells for more, which is the trade.

How fast does a stand-up pouch machine run?

Around 150 pcs/min on the CW-700SQB at 30 m/min, depending on pouch size and film. Smaller pouches allow more pieces per minute; large 500 g formats are limited by the film travel inside the cycle.

Do I need a different film for stand-up pouches?

You need adequate stiffness for the gusset to hold shape, which usually means a PET or BOPP outer layer at 100 to 150 micron total. A structure that runs perfectly on a flat pouch may wrinkle at the gusset fold.

Can a three-side seal machine make zipper pouches?

Some can, with a zipper applicator. The CWZD-600A, for example, is specified for zipper pouches as well as centre-seal and three-side seal formats. Confirm that the applicator is included in the quotation, because it is often an option.

What changeover time should I expect?

Two to four hours for a stand-up pouch size change with two people, one to two hours for a three-side seal change. These figures assume the tooling set is complete and the recipe was saved. Without a saved recipe, add an hour for re-tuning.

Not sure which pouch format your product should use?
Send the fill weight, film structure and a shelf photo of the competing product. We will tell you which format fits, which machine produces it, and what the tooling list looks like for your size range.

Get a Pouch Format Recommendation

Related Resources

● Types of Pouch Making Machines — the full family, including four-side seal and spouted formats.

● What Is a Pouch Packaging Machine and How Does It Work? — process basics before specification.

● Comprehensive Guide to Plastic Pouch Making Machines — a longer buyer’s reference.

Coming next: Gusset Depth and Fill Volume: How the Bottom Fold Sets Your Pouch, and Print Registration on Stand-Up Pouches: Why the Fold Moves.

GET A QUOTE NOW