
A Chinese bag making machine reaches high-speed production when the whole line — film path, servo motion, sealing and stacking — holds its rated rate for a full shift, not for a five-minute demonstration. Two machines quoting the same 250 pcs/min often deliver very different output once your own film runs through them.
Three numbers get called speed in a quote, and only one decides your output. Cycle rate is bags per minute per lane; line speed is metres of film per minute; sustained output is what the machine delivers across a shift after splices and stops.
Two lanes at 250 pcs/min is 500 bags per minute, or 30,000 per hour. At 85% efficiency a shift yields about 204,000 bags. That gap between 500 and 300 effective bags per minute is where projects pay back or stall, so run the numbers before the RFQ with this production capacity calculation method.
Above roughly 120 cycles per minute, mechanical cams stop being the limiting factor and motion control takes over. Feed, seal, cut and punch follow an electronic cam profile and re-phase whenever tension or registration error appears. At 500 bags per minute the whole cycle fits inside 120 milliseconds, which is why dwell shrinks to 60–80 ms.
The CW-800CSD soft loop handle bag machine shows how that plays out: three servos drive the soft-loop conveyor alone, so the handle web accelerates independently of the bag web, at 120 pcs/min on soft loop and 140 pcs/min on patch handle bags.
Film cannot be accelerated by adding a motor, so the web path sets the ceiling. A line at 125 m/min pulls 2.08 metres of film every second, and a 1% tension error becomes 1.25 m/min of web-speed error that shows up as bag length drift. Registration must read a colour mark at full speed, which is why SICK and Datalogic heads are specified on Chinese high-speed machines.
Heat transfer needs time, so the sealing station is the hardest part to design at high cycle rates. Doubling the cycle rate halves the dwell, and a seal does not care how good the servo is: if the interface never reaches temperature across the full bag width, bags fail a drop test while the machine still hits rated output. Narrow low-mass bars, independent temperature zones and chilled support rollers set the seal before stacking. On servo-driven machines such as the CW-1100BS5 high speed bottom sealing machine, bar motion keeps dwell consistent as bag length changes.
Lanes are the cheapest way to add capacity and the easiest way to create a bottleneck. Two or four lanes multiply output without raising line speed, so film handling stays inside a safer envelope; the trade-off moves downstream to punching, folding and stacking.
The CW-400V2 t-shirt bag machine makes the trade-off visible: two 400 mm lanes, 370–700 mm bags, 125 m/min, 250 bags per lane per minute, a 5-tonne hydraulic punch and an automatic stacking table. At 500 bags per minute the stacker works at the same rate as the sealing station.
The advantage is not cheap labour — it is a supply chain that lets a bag making machine manufacturer specify Japanese, German or Taiwanese servos, PLCs and photocells and still quote competitively. Speed is a tolerance problem: frame rigidity, roller concentricity and sealing-bar flatness decide whether a two-lane line really holds 500 bags per minute. Chovyting Machinery has built bag making machines for more than 20 years across side sealing, bottom sealing, vest bag, rubbish bag, pouch and FFS formats, and runs acceptance tests on the buyer’s own film.
Get your speed numbers before you approve the quote
Send your bag type, film, bag size and shift target, and our engineers will confirm the sustained rate in writing.
● Rated speed at your bag size and film, with registration on.
● Servo count and axis assignment: feed, seal, cut, punch, handle web.
● Sealing bar width, temperature zoning, cooling and dwell stability.
120–200 cycles per minute on bag-on-roll lines, 120–140 pcs/min on handle bags, and 250 pcs/min per lane on two-lane t-shirt machines.
No. Output is rated speed times efficiency: 500 pcs/min at 70% delivers 350 bags per minute.
T-shirt and vest bags, bottom seal bags on roll, draw-tape rubbish bags and wicket bags; zipper pouches stay at 60–120 pcs/min.
Consistent gauge, controlled slip and no blocking; a 5% gauge variation becomes bag-length drift.
Run a full shift on your own film at the acceptance test, count bags and record every stop.
High-speed production is no longer a claim about motors or datasheets. It is a claim about how well the film path, servo system, sealing station and support work together at hour eight. Browse the full range of plastic bag making machines to see where each format sits.
● High Speed Bag Making Machine Features, Principle And Application