...
3 Side Seal Pouch Making Machine vs Four Side Seal Machine: Which Pouch Style Fits Your Products?
November 17, 2026

3 Side Seal Pouch Making Machine vs Four Side Seal Machine: Which Pouch Style Fits Your Products?

One extra seal bar does not sound like a different machine category. In practice, three-side seal and four-side seal pouches serve different products, fail in different places, and are produced on machines with different economics. Choosing the wrong one shows up as leakers at the fill line, pouches that bulge on the shelf, or a tooling bill you did not budget for.

This comparison is written for the buyer who has a product and needs to decide which pouch structure to specify — and therefore which machine to buy.

Where the Seals Sit, and Why It Matters

Seal position determines how a filled pouch carries load:

● Three-side seal — two webs sealed on the left, right and bottom edges, open at the top. The pouch is essentially a flat pillow. Load hangs from the top seal and pushes outward on the two side seals.

● Four-side seal — sealed on all four edges, with the top seal closing after filling. The pouch is a flat sachet with a seal frame all round, so load distributes across four seals instead of three.

● Four-side seal with bottom gusset (flat bottom) — the format most people mean when they say “eight-side seal” or “square bottom”. The gusset adds two more seal zones plus corner seals, which is where the higher seal count comes from.

The CW-700SQB square bottom pouch machine is built for the gusseted version; the CWZD-600A covers the three-side seal and centre-seal formats on one platform.

Strength: Where Each Pouch Fails

Failure location is more informative than failure load:

● Three-side seal — the weak point is the bottom seal corners, where the two side seals meet the bottom seal. Three seal bars converging create a triple-thickness zone that cools unevenly, and that is where a 1 kg fill will open under drop test.

● Four-side seal — the load is shared, and failures move to the sealant layer itself rather than the seal junction. This is why sachets hold higher fill weights per unit area than flat three-side pouches.

● Gusseted flat bottom — the corner folds are the critical zone. They are also the hardest to seal because four layers of laminate must be fused without thinning the sealant at the fold.

A practical rule from fill-line experience: three-side seal pouches are comfortable up to about 500 g; four-side seal sachets handle 100 g to 1 kg in small formats; gusseted flat-bottom pouches are the format of choice above 500 g when the pouch must also stand.

Ask for a drop test at your fill weight, not a burst test at an arbitrary pressure. A pouch that passes 0.6 bar burst can still open at the bottom corners after three drops from 1.2 m.

CWZD-600A zipper and three side seal pouch machine

Film Structure and Registration

The seal layout changes what the film has to do:

● Three-side seal — two webs mean two registration systems, or one web folded at the top. Aligning print across two independently fed webs is the harder route; most machines fold a single web to avoid it.

● Four-side seal — a single web, sealed to itself at all four edges, so registration is a single-channel problem. This is mechanically simpler and faster to set up.

● Gusseted flat bottom — one web, but with fold lines that must align with print. The gusset forming plates position the film mechanically, so print alignment is set by the forming station, not by the photocell alone.

Film thickness follows the same logic. Three-side seal pouches at 70 to 120 micron are common; four-side seal sachets often run thinner, 60 to 100 micron, because the seal frame carries the load. Gusseted pouches need 100 to 150 micron for the folds to hold shape.

Output and Machine Choice

Speed is a function of seal count as much as of drive quality:

● CWZD-600A — 40 to 150 pcs/min depending on format, pouch length 70 to 500 mm, 24 to 26 kW, with a six-times skip-feed design for long pouches and an automatic waste film rewinding unit. Suitable for three-side seal, centre seal, zipper and centre-seal gusset pouches.

● CWZD-600ZF+SZ — 30 to 140 pcs/min, pouch length 75 to 580 mm, with double servo and double inverter drive plus a bridge-type heavy pressing seal structure. The heavy pressing head is what allows a longer, lower-temperature seal without slowing the cycle.

● CW-700SQB — 150 pcs/min and 30 m/min for gusseted square bottom pouches, 150 to 650 mm width, 1,300 mm maximum film width.

Four-side seal formats generally run slower per stroke than three-side seal, because each pouch needs four seal operations rather than three, and the top seal is often a separate station. Budget 20 to 30 percent less output for the same machine class.

Tooling and Changeover

Tooling is the hidden cost in pouch production, and the two formats differ sharply:

● Three-side seal — tooling is mostly seal bar position and a cutter. A new size may need new bars but often reuses the frames. Changeover in one to two hours is realistic.

● Four-side seal — the seal frame is size-specific. Each pouch size needs its own frame or inserts, so the tooling cost per size is higher and the changeover is longer.

● Gusseted flat bottom — gusset forming plates are machined per depth and width. This is the most expensive tooling of the three, and the reason buyers with wide product ranges often standardise on two or three sizes.

Before ordering, ask for a tooling matrix: which pouch sizes are covered by standard tooling, which need custom work, and what each set costs. A machine quoted at USD 60,000 with USD 18,000 of tooling for four sizes is a different proposition from one quoted at 75,000 with tooling included.

CWZD-400BFS four side seal pouch making machine

Which Pouch Fits Which Product

Match the format to the product rather than to the machine:

● Coffee and ground products — gusseted flat bottom with a degassing valve. The pouch must stand and hold 250 to 1,000 g; a flat sachet is only used for single-serve.

● Snack foods — gusseted or three-side seal depending on fill volume. Small 30 to 80 g packs are usually three-side seal or pillow; 150 g and above move to gusseted.

● Powders and granules — four-side seal sachets for single doses, gusseted for retail. Powder migration through seals is a real issue, so seal width matters more than seal count.

● Liquids and pastes — four-side seal sachets with a wide seal frame; three-side seal is used for small volumes where the bottom corners are reinforced.

● Pet food and treats — gusseted flat bottom almost exclusively, for shelf presence and 1 to 3 kg fills.

● Retort applications — four-side seal or gusseted with retort-grade sealant, and a machine capable of holding seal pressure long enough for the thicker sealant layer.

Five Questions That Decide It

Answer these before requesting quotations:

● What is the fill weight? — the single strongest predictor of format. Under 100 g, flat sachets. Over 500 g, gusseted.

● Must the pouch stand on a shelf? — if yes, the gusset is mandatory and the decision is made.

● What is the drop and compression requirement? — distribution through retail usually implies a drop test that a three-side seal pouch at 500 g will struggle to pass.

● How many sizes and how often do they change? — tooling and changeover economics favour fewer sizes.

● What filling equipment will run it? — premade pouch fillers are format specific. Confirm the filler can handle the pouch before committing to the machine.

For a broader view of bag structures, see nine types of polythene bags by bag structure, and for the machine family see types of pouch making machines.

Mistakes That Cost a Season

Three patterns we see repeatedly:

● Specifying the cheapest pouch, then failing the drop test — the remedy is a new machine and new tooling, not a film change. Test at your real fill weight before ordering equipment.

● Buying a four-side seal machine for three-side seal work — it will run the job, but at lower output and with tooling you did not need. Buy the format the product requires.

● Underestimating changeover — a factory switching size twice a week loses more to changeover than it gains from a faster machine. Count the switches before comparing speeds.

Frequently Asked Questions

3 side seal or 4 side seal: what is the difference?

A three-side seal pouch is sealed on the left, right and bottom edges with the top left open for filling. A four-side seal pouch is sealed on all four edges, with the top closed after filling. The fourth seal distributes load better and allows higher fill weights in a small format.

Which pouch is stronger, three-side or four-side seal?

Four-side seal, generally. Load is shared across four seals instead of three, and the weaker triple-thickness corner of a three-side seal pouch is eliminated. The difference becomes noticeable above about 500 g fill weight.

What does “8 side seal” mean on a pouch machine?

It refers to the number of seal zones on a gusseted square-bottom pouch: four side seals plus four corner or gusset seals. It is a description of the pouch construction, not of eight separate seal bars on the machine.

Can one machine make both pouch formats?

Sometimes. Machines specified for multiple formats, such as the CWZD-600A, cover three-side seal, centre seal and zipper pouches. Four-side seal with a gusset usually requires a dedicated gusset forming station, which is a different machine layout.

How much does pouch tooling cost per size?

For three-side seal, a new size is often a set of seal bars and a cutter. For four-side seal, the seal frame is size specific. For gusseted flat bottom, forming plates are machined per depth and width, making it the most expensive of the three. Request a tooling matrix with the quotation.

Which format suits a 1 kg fill?

A gusseted flat-bottom pouch, in most cases. Three-side seal pouches at 1 kg are possible but need reinforced corners and a heavier film, and they will not stand on a shelf. Four-side seal sachets at 1 kg exist but are usually industrial formats.

Does a four-side seal pouch need a different film?

It can use a similar laminate, often slightly thinner because the seal frame carries more load. Sealant layer thickness matters more than total thickness: a 30 micron sealant layer performs better than a 100 micron structure with 15 micron of sealant.

Have a fill weight and a shelf photo, but no format decision?
Send both. We will match the pouch construction to your product, list the machine and tooling needed, and flag any fill-line compatibility issue before you commit.

Ask for a Format Comparison

Related Resources

● Types of Pouch Making Machines — the family overview with format ranges.

● 9 Types of Polythene Bags by Bag Structure — how seal layout defines a bag category.

● Comprehensive Guide to Plastic Pouch Making Machine — specification detail for buyers.

Coming next: Seal Frame Width vs Seal Strength on Four-Side Sachets, and Degassing Valves on Gusseted Coffee Pouches.

GET A QUOTE NOW